The device is extensively documented in the User Guide, including instructions in use of software to communicate with it. However, the battery may not provide optimal performance and life over the entire temperature range. Further details are discussed in the Firmware section , below. The unit can either start logging automatically, or after pressing the start button. It shows a little running-man icon on the left side while logging. To store a waypoint while logging, one must be in the menu that displays latitude and longitude.
|Published (Last):||7 December 2011|
|PDF File Size:||7.6 Mb|
|ePub File Size:||10.50 Mb|
|Price:||Free* [*Free Regsitration Required]|
Megis If the user wants to use M to record the coordinate for matching the GPS coordinate of the picture in the camera, because the integration of the two parties is performed under the comparison of the time, it is recommended for the user to adjust the clock time in the camera to match the GPS time in the M Back to Setting Mode The links are taken from a post in the [ http: Utility main screen includes four sub pages You can get the driver on the Web site of the manufacturer of the chip set: Note that the NMEA Interface Standard specifies serial communication speed at baud, although the M is capable of exceeding this speed when connected to a suitable host.
Before you start,make sure that the following items are included in your package. BT software works on Linux. Use AA alkaline batteries or rechargeablebatteries for up to 12 hours of operation.
Pressing the Enter button logs the waypoint, and confirms it by briefly displaying a little flag icon in the bottom left corner. This release still allows one to set specific logging parameters while the device is switched on.
To print the manual completely, please, download it. The M supports distance and time logging modes, kilometer and mile distance units, and 3 languages English, Traditional Chinese, and Simplified Chinese. Even if Mtkbabel allows to set higher logging intervals 1 s, 1 mthe firmware seems to overwrite this with the settings from the menu. Since it is hard to buy a new Holux M in India, I have been patching it, soldering it a few times now.
It features a x32 pixel monochrome LCD display with green backlight to show current position and device status. I do recharge the battery via my USB cable, while I download the tracks.
Guess I would qualify as a low user, although I am rather tall. If you manually set the logging rate under 1s, the device will raise it automatically until the next logging starts. Holuc did not get them with gpsbabel. Describe the threshold that photo isdiscarded. T echnologyInc. The download time takes about 4 min if full memory usage. Use AA alkaline batteries or rechargeable batteries for up to 12 hours of operation.
A user-friendly software utility is provided with the following functions: M on the Plane. The M can record up to, positions, each position including longitude, latitude, time, and altitude. Superior sensitivity, up to dBm. Setup the Baud rate: The Holux M is not waterproof. Powered by one AA battery. The M should now be connected. I just leave the unit connected some hours and it has not needed a fresh battery for many weeks now.
Table of Contents Add to my manuals Add. If one expects to be inundated or to use it in the rain, it should be enclosed in a waterproof plastic container, a zip-closure polyethylene freezer bag, or a zip-closure vinyl envelope designed for electronics. Obtain the beta version of gpsbabel and type:. Since I am tall, falling has to be avoided. Setting and back to Setting mode Note: Recent firmware releases as of — are versions 1.
HOLUX M-241 Quick Manual
Yes, the Funtrek GM can support third party software. Just need to do some simple settings then the third party software will embedded on our system. But first of all, please make sure your third party software can match the conditions below: It can operated under WinCE 5. And you can do similar setting on your 3th party software as same as our example, it can be added many kind of application software into GM Please try to contact our sales unit, it would be processed by special project. The software ezTour Plus can only operate under Windows platform. Buy a new battery for FunTrek ?
FAQ – frequently asked questions