FLUKE 8505A PDF

Mijind Any subsequent activation of External Reference mode replaces the software number with the actual external reference value. The temporary zero correction factors are applied in dc volts V or ohms Z whenever the M2 command is in effect i. Once a a with the instrument is achieved, parts of this section will serve as a quick reference. Software calibration for each function can be accomplished locally or remotely. The Average mode is disabled OO.

Author:Mazulabar Kikora
Country:Angola
Language:English (Spanish)
Genre:Technology
Published (Last):1 May 2009
Pages:245
PDF File Size:17.68 Mb
ePub File Size:20.81 Mb
ISBN:412-5-21990-351-2
Downloads:24938
Price:Free* [*Free Regsitration Required]
Uploader:Faecage



Mijind Any subsequent activation of External Reference mode replaces the software number with the actual external reference value.

The temporary zero correction factors are applied in dc volts V or ohms Z whenever the M2 command is in effect i. Once a a with the instrument is achieved, parts of this section will serve as a quick reference. Software calibration for each function can be accomplished locally or remotely. The Average mode is disabled OO. Both the A and the A assume the same configuration at power up as that described for A, with the following exceptions: Data lines DB0-DB7 are used for bidirectional data flow.

In Autoranging, the multimeter selects the range offering maximum resolution for the measured value. Error 7 External Reference error — voltage on one input exceeds 20V dc. Calibration mode entries are applied to the reading as follows; a. A check sum error 25 condition would then be set. Operation of the multimeter is straightforward.

Perform V DC Flike for interna! If dc volts, ohms, or dc amps is selected, extended resolution Flule mode is disabled, the filter is not changed, and the sample is set to S7. Fluke A used or new for sale at used-line This signal occurs after the measurement is complete, but before a new trigger is accepted. Nulls are discarded and not stored. Separate modules for averaging ac or rms ac measurements are available: Power must not be cycled on or off when the Calibration mode is activated rear panel Calibration Switch on.

The combination of the attenuator and feedback-controlled amplifier give gain factors a 1, 10, or and attenuation factors of 8 or Front Panel Push Buttons cont A Mathematic Operations; To store the displayed value as an offset orscaling value and enter the respective mode: Interrupts are used to divert the microprocessor from the main program to service other routines. Averaging mode is locked out: The following trigger mode transitions will occur when halt is used: Special instructions for inspection and claims are included with the shipping container.

Samples taken are synchronous to the line frequency for local operation. A numeric value may be entered using a store sequence. Zero mode is enabled with all temporary zero correction values set to 0. If another G1 command is sent before a flukke reading is triggered, no error 00 is identified in the response. Cleaning Instructions If Calibration mode is off, the values are stored in a temporary memory and do not affect Calibration Memory entries.

Module Removal When initially commanding an ac volts function, VA2 for ac coupling or C2 for dc coupling must be used, when the multimeter isalready set for either of the other two ac volts functions, ac volts high accuracy can be selected by using S2 only.

Zero may be turned off at any time. Refer to Calibration Mode later in this section. Depending on the number of entries being cleared, several seconds may be necessary to complete this operation. Either the normally displayed value or programmed numerics may be used for the limit values. NOTE Flashing indicators in the digit or flukee display are a warning only; they have no effect on instrument operation.

Error 2 Filter module faulty or not installed. Most 10 Related.

FAWLTY TOWERS SCRIPTS PDF

Fluke 8505A Instruction Manual

Both models excel in dc accuracy, resolution, versatility and speed. The A uses a fast thermal rms sensing technique for measuring ac which very significantly advances the state-of-the-art for ac measurements using a system DMM. It is several times more accurate than the calculating type of true-rms Converter and is unmatched by any other DMM. Basic ac accuracy uncertainty is reduced to parts per million, 24 hours for frequencies from 40 Hz to 20 kHz. That approximates the accuracy you can expect using traditional thermal transfer techniques that typically take several minutes for each measurement.

CLASIFICACION COXARTROSIS PDF

Fluke 8505A Manuals & User Guides

Common mode voltages, resulting from currents and voltage drops between two points otherwise electrically common, may cause significant errors. This warranty shall not apply to fuses, disposable batteries rechargeable type batteries are warranted for daysor any product or parts which have been subject to misuse, neglect, accident, or abnormal conditions of operations. S 1 ; V AC Enhanced 3. Digit 8 is used only on the 10V dc range to yield IVz digit resolution. The exponent is range dependent in ohms function 1 for ohm ranges, 4 for kohm ranges, and 7 for Mohm ranges. Replacement of Calibration Memory may be required. The following sequence can be used to select any of the five filter modes: Keep gain correction on this range.

KANT VIDA DOCTRINA ERNST CASSIRER PDF

Fluke 8505A Digital Multimeter OPT 05 08a

Arashisar The applications may be used as examples to aid in familiarization with the multimeter. The A and A do not use a separate module for calibration memory entries calibration memory is a standard part of the Controller module. Options and Accessories For the A and A, a command string may have up to 59 characters. Scaling or External Reference fpuke Offset can be used in combination to display percentage variation. If error 25 remains, it may be necessary to first clear, and then re-enter, all correction factors, zero values, and the calibration date or instrument identification number. Calibration Date and Identification Number Remote interfaces, ac converters, a current converter, and an ohms converter are among the numerous options and accessories available for use with the a. There are two methods for making this selection.

C FOR GAME PROGRAMMERS MICHAEL J.DICKHEISER PDF

Fluke 8505A Manuals

.

Related Articles