CHROMA 6314 USER MANUAL PDF

The low range provides better resolution at low voltage measurements. All parameters of Load are set through Chroka. Chroma Manual Even though other OSes might be patible as well, we do not remend apying this release on atforms chroma a user janual other than the ones specified. It is designed for applications in research and development, production, and incoming inspection. L for safety and airflow Channel Number The channel number of a specific Load is determined by the location of that module in relation to the farthest left side of Mainframe.

Author:Dalabar Maugis
Country:Honduras
Language:English (Spanish)
Genre:Education
Published (Last):28 June 2014
Pages:11
PDF File Size:4.87 Mb
ePub File Size:4.71 Mb
ISBN:432-6-41695-306-4
Downloads:44395
Price:Free* [*Free Regsitration Required]
Uploader:Tygoshicage



Targ If your application requires a greater power or current capacity than one module can provide, you have to connect load modules in parallel in CC or CR mode.

Barry McDaniel 1 years ago Views: There is a double pole RC filter of input voltage, so high frequency parts will be removed. The nominal output power is More information. Chroma Manual Even though other OSes might be patible as well, we do not remend apying this release on atforms chroma a user manual other than the ones specified. In remote mode programmed value cannot be over boundary.

This warranty is in lieu of all other warranties, expressed or implied, and no representative or person is authorized to represent or assume for Chroma any liability in connection with the sale of our products other than set forth herein. The line fuses will Overcurrent When Load is operating in CR or CV mode, it is possible for a module to attempt to sink current more than it is rated for.

The Chroma Mainframe has room for four single-width Loads, or two double-width Loads In addition, the remote control commands will be compatible between the and the A series without needing to re- writing any remote control programs. Updated versions of this document More information.

To make this website work, we log user data and share it with processors. When local operation is in effect, you can select a channel, and use the display as well as keypad on the front panel to control the Load.

The Load module also executes a self-test that checks firmware and communication with Mainframe. Immediately after power is applied, local operation will be in effect. Load modules occupy either one or two slots.

The nominal output power is. Press MODE key first, then ,anual or key to select the current range. The change of modes will affect the module, so will the change of range. Voltage Ranges Low, High There are two voltage ranges for voltage measurement and Von voltage setting.

Special disclaimers apply to these instruments. The unit has been factory set to the correct line voltage. If the instrument is defective as a result of misuse, improper repair, or abnormal conditions or operations, repairs will be billed at cost. Unlike conventional supplies with fixed output ratings. Power Cord, Manual Load Module: The actual value of electronic short is dependent on the mode and range that are active when the short is turned on. The load can be dhroma in constant current, constant voltage, constant power and constant resistance.

The A load module uses a photo coupler for isolation between the. The A series has a self-diagnosis routines to maintain instrument performance. Dynamic Loading and Control Amnual A loads offer high uswr, programmable dynamic load simulation and control capability.

A Cheat Sheet Open Loop Vector The following procedure is a supplement to supplied with this equipment and will guide the user in properly wiring the A and.

Add to Inquiry Cart Data Sheet. Transportation to the factory or service center is to be prepaid by purchaser. Click here to unsubscribe. This feature reduces overall noise level because the fans do not always run at the maximum speed.

The low range is used for input voltage in low voltage range while the high range for input voltage over low voltage range. Figure The Front Panel of the Electronic Load On the front panel of the electronic load as shown in Figure there are two groups of keypads. Mainframes accept the user- installable A series load modules for.

Determine the position for the Hands-free phone in the elevator phone More information. There are also higher wattage modules that may be mixed and matched for an even more versatile system.

Turn on the Load by the power switch on the front panel of the Mainframe and observe chroa display. In CV mode it is equivalent to the programming of zero voltage. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications. Because some Load has two channels in one module, channel 1 and 2 are always on the farthest left slot of the Mainframe, and channel 7 and 8 on the farthest right.

The waveforms programmable parameters include: Chroma A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among chroa load modules.

Mankal Ranges Low, High Resistance can be programmed in either of the two ranges, low range and high range. Related Posts.

INTRODUCTION TO LINUX BY MACHTELD GARRELS PDF

bepannaah.me

Class B devices have a Federal Communications More information. Measurement and Load Cables 2. L for safety and airflow Channel Number The channel number of a specific Load is determined by the location of that module in relation to the farthest left side of Mainframe. Easy programming More information. OCP Test By simply uuser the channel and setting the OCP parameters start current, end current, step current and dwell time from the front panel, the A series provides a fast and easy OCP testing solution. This warranty is in lieu of all other warranties, expressed or implied, and no representative or person is authorized to represent or assume for Chroma any liability in connection with the sale of our products other than set forth herein. The A series has self-diagnosis routine to maintain instrumental performance all the time.

DECRETO 4735 DE 2009 PDF

CHROMA 6314 USER MANUAL PDF

Faesho Loads can be combined in the Mainframe in any order. The A series has a self-diagnosis routines to maintain instrument performance. Chroma assumes no liability for the customer s failure to comply with these requirements. It will also show the user how to More information.

Related Articles